XIB-E【PDF 17/64 页】BOARD INTERFACE ETHERNET

13页 14页 15页 16页 [17页]18页 19页 20页 21页

XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>

Binary Commands

Sending and receiving parameter values using binary commands is the fastest way to change

operating parameters of the module. Binary commands are used most often to sample signal

strength (RS parameter) and/or error counts; or to change module addresses and channels for

polling systems when a quick response is necessary. Since the sending and receiving of

parameter values takes place through the same serial data path as 'live' data (received RF

payload), interference between the two types of data can be a concern.

Common questions about using binary commands:

What are the implications of asserting CMD while live data is being sent or received?

After sending serial data, is there a minimum time delay before CMD can be asserted?

Is a time delay required after CMD is de-asserted before payload data can be sent?

How does one discern between live data and data received in response to a command?

The CMD pin [pin 5] must be asserted in order to send binary commands to the module. The

CMD pin can be asserted to recognize binary commands anytime during the transmission or

reception of data. The status of the CMD signal is only checked at the end of the stop bit as the

byte is shifted into the serial port. The application does not allow control over when data is

received, except by waiting for dead time between bursts of communication.

CMD (pin 5) must be asserted in order to send binary commands to an XStream Module. CMD

can be asserted to recognize commands anytime during transmission or reception of data. A

minimum time delay of 100 祍 (after the stop bit of the command byte has been sent) must be

observed before pin 5 can be de-asserted. The command executes after all parameters

associated with the command have been sent. If all parameters are not received within 0.5

seconds, the module aborts the command and returns to Idle Mode. Note: When parameters are

sent, they are always two bytes long with the least significant byte sent first.

Commands can be queried for their current value by sending the command logically ORed with

the value 0x80 (hexadecimal) with CMD asserted. When the binary value is sent (with no

parameters), the current value of the command parameter is sent back through the DO pin.

Figure?11. Binary燙ommand燱rite爐hen燫ead?/DIV>

Signal?4爄s燙MD?pin?)?/DIV>

Signal?1爄s爐he燚IN?pin?)爏ignal爐o爐he爎adio?/DIV>

Signal?2爄s爐he燚OUT?pin?)爏ignal爁rom爐he爎adio?/DIV>

Signal?3爄s?/DIV>

?pin?)?/DIV>

?/DIV>

In爐his爂raph,燼爒alue爓as爓ritten爐o燼爎egister燼nd?/DIV>

then爎ead爋ut爐o爒erify爄t.燱hile爊ot爄n爐he爉iddle?/DIV>

of爋ther爎eceived燿ata,爊ote爐hat爐he?/DIV>

爏ignal?/DIV>

outlines爐he燿ata爎esponse爋ut爋f爐he爉odule.?/DIV>

?/DIV>

IMPORTANT: For the XStream Module to recognize a binary command, RT (DI2 Configuration)

Command must be issued. If binary programming is not enabled (RT ` 1), the

module will not recognize that the CMD pin (Pin 5) is asserted and therefore will not

recognize the data as binary commands.

牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>

17?/DIV>

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式